螺桿鼓風機日常運行維護知識

隨著螺桿鼓風機需求量日益提升，已廣泛應用到水處理、冶煉高爐、洗煤廠、礦山浮選、化工造氣、真空等領域，主要是因?yàn)楣娘L(fēng)機外形美觀，穩定性好，維護方便。

With the increasing demand of screw blower, it has been widely used in water treatment, smelting blast furnace, coal washing plant, mine flotation, chemical gasification, vacuum and other fields, mainly because of its beautiful appearance, good stability and convenient maintenance.

（1）鼓風機運行時，應定期檢查鼓風機進、排氣的壓力與溫度，冷卻用水或油的液體、壓力與溫度、空氣過濾器的壓差等。做好日常讀表記?，并進行分析對比。

(1) During the operation of the blower, the pressure and temperature of the inlet and outlet of the blower, the liquid, pressure and temperature of the cooling water or oil, and the pressure difference of the air filter should be checked regularly. Do a good job in daily reading and recording, and make analysis and comparison.

（2）定期清洗檢查空氣過濾器，保持其正常工作。

(2) Clean and check the air filter regularly to keep it working normally.

（3）注意進氣溫度對鼓風機（離心式）運行工況的影響，如排氣容積流量、運行負荷與功率、喘振的可能性等，及時調整進口導葉或蝶閥的節流裝置，克服進氣溫度變化對容積流量與運行負荷的影響，使鼓風機安 全穩定運行。

(3) Pay attention to the influence of intake air temperature on the operation condition of blower (centrifugal type), such as exhaust volume flow, operation load and power, possibility of surge, etc. timely adjust the throttle device of inlet guide vane or butterfly valve to overcome the influence of intake air temperature change on volume flow and operation load, so as to ensure the safe and stable operation of blower.

（4）經常注意并定期測聽機組運行的聲音和軸承的振動，即采取措施，必要時應停車檢查，找出原因后，排除故障。

(4) Pay attention to and regularly listen to the running sound of the unit and the vibration of the bearing, that is, take measures, stop the machine for inspection if necessary, and remove the fault after finding out the cause.

（5）嚴禁離心鼓風機機組在喘振區運行。

(5) It is strictly forbidden for centrifugal blower unit to operate in surge zone.

（6）按說明書的要求，做好電動機或齒輪箱的檢查和維護。

(6) Check and maintain the motor or gearbox according to the instruction.

（7）開機后200h應換油。如果被更換的油δ變質，經過濾機過濾后仍可重新使用。開機后500h作油樣分析，以后?月抽一次油樣分析，發現油變質應即時換油。油號必須符合規定，嚴禁使用其他牌號的油。

(7) The oil should be changed 200 hours after the first startup. If the replaced oil δ deteriorates, it can still be reused after being filtered by the filter. The oil samples were analyzed 500 hours after the first start-up. After that, the oil samples were taken once a month. If the oil was found to be deteriorated, the oil should be changed immediately. The oil grade must meet the requirements. It is strictly forbidden to use other grades of oil.

（8）檢查油箱中的油λ，不得低于油λ線，看油壓是否保持正常值。經常檢查軸承出口處的油溫，不應超過50℃，并根據情況調節油冷卻器的冷卻水量，使進水軸承前的油溫保持在30～40℃之間。

(8) Check the oil λ in the oil tank, which shall not be lower than the minimum oil λ line, to see if the oil pressure remains normal. Always check the oil temperature at the outlet of the bearing, which should not exceed 50 ℃, and adjust the cooling water volume of the oil cooler according to the situation, so that the oil temperature before the inlet bearing is kept between 30 ℃ and 40 ℃.

（9）定期清洗濾油器。經常檢查空氣過濾器的阻力變化，定期進行清洗和維護，使其保持正常工作。

(9) Clean the oil filter regularly. Check the resistance change of air filter regularly, clean and maintain it regularly to keep it working normally.

綜上所述，一臺好的螺桿鼓風機必得配備一個好的使用者，這個人需對鼓風機日常運行維護知識有個充分的了解，只有知識，維護經驗十足的人，才能使得鼓風機使用壽命延長，工作效率才能提高。

To sum up, a good screw blower must be equipped with a good user. This person needs to have a full understanding of the daily operation and maintenance knowledge of the blower. Only those with strong knowledge and full maintenance experience can prolong the service life of the blower and improve the work efficiency.